manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

DISASSEMBLY/REASSEMBLY

2, “A”

2, “A”

“A”: Apply oil

1. Bracket sub assembly

(including fuel filter)

2. Grommet
3. Tube
4. Housing
5. Lead wire
6. Fuel level sensor

(Fuel sender gauge)

7. Fuel pump
8. Cushion
9. Bracket

10. Spacer

NOTE

When removing fuel level sensor (1), press snap-fit part (2) and
slide it in the arrow direction as shown in the figure.

When installing fuel level sensor to housing, fit fuel level sensor
securely.

CAUTION:

While removing fuel level gauge, do not contact resis-
tor plate [1] or deform arm [2]. It may cause fuel level
gauge to fail.

When removing grommet from fuel tube or bracket
sub assembly, be very careful not to cause damage to
grommet installed section (sealed section in bore).
Should it be damaged, replace it with new one, or fuel
will leak from that part.

[2]

[1]

2

1

INSTALLATION

1) Clean mating surfaces of fuel pump assembly (1) and fuel tank.
2) Install new gasket (2) and plate (3) to fuel pump assembly then

install fuel pump assembly to fuel tank.

6C-10

ENGINE FUEL

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Abarth 595 Owner'S Handbook Manual preview
595
Бренд: Abarth Страницы: 176
Acdeos AXS FL Installation Instruction preview
AXS FL
Бренд: Acdeos Страницы: 7
Acdeos AXS FL Manual preview
AXS FL
Бренд: Acdeos Страницы: 38
Camoplast T4S User Manual preview
T4S
Бренд: Camoplast Страницы: 60
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
Subaru SPLASH GUARD Installation Manual preview
SPLASH GUARD
Бренд: Subaru Страницы: 3
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Бренд: DAF Страницы: 18
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Бренд: Ford Страницы: 256
RBO RBO4038 Product Manual preview
RBO4038
Бренд: RBO Страницы: 15
Reese Explore 63153 Instruction Manual preview
63153
Бренд: Reese Explore Страницы: 9
Radical Sportscars SR 3 SL Owner'S Handbook Manual preview
SR 3 SL
Бренд: Radical Sportscars Страницы: 44
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Бренд: DEFA Страницы: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Бренд: Steelmate Страницы: 14
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Бренд: Vauxhall Страницы: 95
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300

Бренды по названию

Популярные бренды

Загрузить еще бренды