manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

Seat belt with ELR and pretensioner

The seat belt with ELR and a pretensioner has a pretensioner mechanism which operates in linkage with the air
bag in addition to the above described ELR. The pretensioner takes up the sag of the seat belt in occurrence of
a front collision with an impact larger than a certain set value, thereby enhancing restraint performance.

Driver and front passenger air bags and seat belt pretensioners

With the air bag system which includes air bags for both the driver’s and passenger’s sides as well as the seat
belt pretensioners, the pretensioner takes up the sag of the seat belt, the driver air bag (inflator) module is
deployed from the center of the steering column and the passenger air bag (inflator) module from the top of the
instrument panel in front of the front passenger seat in occurrence of a front collision with an impact larger than
a certain set value to supplement protection offered by the driver and front passenger seat belts.

SEAT BELT PRETENSIONER (IF EQUIPPED)

Some seat belts of the driver and front passenger seats are provided with a pretensioner as an optional function
unit. The pretensioner is incorporated in retractor assembly and controlled by SDM as one of air bag system com-
ponents. It will be activated at the same time as the air bag when an impact at the front of vehicle exceeds the
specified value.
When servicing seat belt (retractor assembly) with pretensioner, be sure to observe all WARNINGS and CAU-
TIONS in this section and SERVICE PRECAUTIONS under ON-VEHICLE SERVICE in SECTION 10B.

CAUTION:
Do not reuse the seat belt pretensioner (retractor assembly) that has operated but replace it with a
new one as an assembly. For checking procedure of its operation, refer to SERVICE PRECAUTIONS
under ON-VEHICLE SERVICE in SECTION 10B.

SEAT BELT

DIAGNOSIS

For diagnosis of the seat belt pretensioner, refer to SECTION10B.

INSPECTION AND REPAIR REQUIRED AFTER ACCIDENT

After an accident, whether the seat belt pretensioner has been activated or not, be sure to perform checks and
repairs described on REPAIRS AND INSPECTIONS REQUIRED AFTER ACCIDENT under DIAGNOSIS in SEC-
TION 10B.

RESTRAINT SYSTEM

10-3

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Daihatsu Mira Manual preview
Mira
Бренд: Daihatsu Страницы: 340
Eaton Green Motion Building Quick Start Manual preview
Green Motion Building
Бренд: Eaton Страницы: 12
Alpine KCE-G7QI Installation preview
KCE-G7QI
Бренд: Alpine Страницы: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Бренд: Whispbar Страницы: 15
Pacbrake C44059 Installation Manual preview
C44059
Бренд: Pacbrake Страницы: 14
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
Atera 080 705 User Information preview
080 705
Бренд: Atera Страницы: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Бренд: Black Horse Страницы: 5
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Бренд: Mazda Страницы: 3
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Бренд: FALCON RIDGE Страницы: 6
Yakima LockNLoad LightenUp Manual preview
LockNLoad LightenUp
Бренд: Yakima Страницы: 13
Gator ARV43M Instruction Manual preview
ARV43M
Бренд: Gator Страницы: 5
GEMINI TECHNOLOGY 514F User Manual preview
514F
Бренд: GEMINI TECHNOLOGY Страницы: 9
GMC Chevrolet CAMARO 1969 Owner'S Manual preview
Chevrolet CAMARO 1969
Бренд: GMC Страницы: 92
HG2 REAR RUNNER Install Manual preview
REAR RUNNER
Бренд: HG2 Страницы: 6
AEM 21-5011 Installation Manuallines preview
21-5011
Бренд: AEM Страницы: 5
CEMO DT-Mobil Easy 200 L Original Operating Instructions preview
DT-Mobil Easy 200 L
Бренд: CEMO Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды