manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

ACCELERATOR CABLE ADJUSTMENT

With accelerator pedal depressed fully, check clearance between
throttle lever (1) and lever stopper (2) (throttle body), it should be
within following specification.

Clearance “b” : 0.5 – 2.0 mm (0.02 – 0.07 in.)
(With pedal depressed fully)

With throttle valve closed, check accelerator pedal play, it should
be within following specification.

Pedal play “a”: 2 – 7 mm (0.08 – 0.27 in.)

If measured value is out of specification, adjust it to specification
with cable adjusting nut (3).

1

2

“a”

“b”

3

IDLE SPEED/IDLE AIR CONTROL (IAC) DUTY
INSPECTION

Before idle speed/IAC duty check, check for following conditions.

Lead wires and hoses of engine / emission control systems are
connected securely.

Accelerator cable has some play, that is, it is not tight.

Valve lash is checked and adjusted according to maintenance
schedule.

Ignition timing is within specification.

All accessories (wipers, heater, lights, A / C, etc.) are out of ser-
vice.

Air cleaner has been properly installed and is in good condition.

ECM/PCM does not detect any malfunction DTC.

After above conditions are all confirmed, check idle speed and IAC
duty as follows.

NOTE:
Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T vehicle), set
parking brake and block drive wheels.

6E1-50

ENGINE AND EMISSION CONTROL SYSTEM

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
Pacbrake 10475 Installation Manual preview
10475
Бренд: Pacbrake Страницы: 9
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Бренд: iDataLink Страницы: 30
Saab B205 Installation Instructions Manual preview
B205
Бренд: Saab Страницы: 10
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Бренд: Taffio Страницы: 8
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Бренд: Mercedes-Benz Страницы: 30
Mazda 2 2016 Owner'S Manual preview
2 2016
Бренд: Mazda Страницы: 720
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Бренд: FVC Страницы: 8
v.link VL2-DVD900 Manual preview
VL2-DVD900
Бренд: v.link Страницы: 19
Belkin F8J034 User Manual preview
F8J034
Бренд: Belkin Страницы: 30
Mitsubishi FTO Series Handbook preview
FTO Series
Бренд: Mitsubishi Страницы: 141
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Бренд: Edelbrock Страницы: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Бренд: GMC Страницы: 439
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Бренд: FIRRAK Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды