manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

FRONT SEAT BELT WITH PRETENSIONER

WARNING:

Never attempt to disassemble or repair the seat belt
pretensioner (retractor assembly). If any abnormality
is found, be sure to replace it with new one as an as-
sembly.

Be sure to read SERVICE PRECAUTIONS in this sec-
tion, before starting to work and observe every pre-
caution during work. Neglecting them may result in
personal injury or unactivation of the seat belt preten-
sioner when necessary.

REMOVAL

1) Disconnect negative battery cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYS-

TEM of SERVICE PRECAUTIONS under ON-VEHICLE SER-
VICE in SECTION10B.

3) Remove center pillar lower trim.
4) Disconnect Yellow connector (1) for seat belt pretensioner.

a) Release locking of lock lever
b) After unlocked, disconnect to connector

5) Remove front seat belts from the vehicle in the same way as in

REMOVAL of FRONT SEAT BELT WITHOUT PRETENSION-
ER.

1

b)

b)

a)

1

INSPECTION

WARNING:
Never measure resistance of pretensioner or disas-
semble it. Otherwise, personal injury may result.

CAUTION:
If seat belt pretensioner (retractor assembly) was
dropped from a height of 30 cm (1 ft) or more, it should
be replaced.

RESTRAINT SYSTEM

10-7

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Бренд: Jeep Страницы: 673
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Бренд: RAM Commercial Страницы: 12
Vauxhall Meriva Quick Reference Manual preview
Meriva
Бренд: Vauxhall Страницы: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Бренд: Vauxhall Страницы: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Бренд: Vauxhall Страницы: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Бренд: Vauxhall Страницы: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Бренд: VBC Racing Страницы: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Бренд: Vauxhall Страницы: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Бренд: Vauxhall Страницы: 2
Vauxhall Antara Owner'S Manual preview
Antara
Бренд: Vauxhall Страницы: 236
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
U & Me Brothers LK-168A Manual preview
LK-168A
Бренд: U & Me Brothers Страницы: 6
muth signal mirror Instalation Instructions preview
signal mirror
Бренд: muth Страницы: 10
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Sears 580.32601 Owner'S Manual preview
580.32601
Бренд: Sears Страницы: 41
Park-Daddy PD50AA Installation Manual preview
PD50AA
Бренд: Park-Daddy Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды