manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

1

INSPECTION

Seat belts and attaching parts can affect the vital components and
systems of a vehicle.
Therefore, they should be inspected carefully and replaced with
genuine parts only.

Seat belt
Its webbing or strap should be free from damage.

Retractor assembly
It should lock webbing when pulled quickly.
The front seat belt retractor assembly (1) should pass the above
inspection and should lock webbing even when tilted (approx.
15

) toward the fore and aft or right and left directions.

Anchor bolt
Anchor bolts should be torqued to specification.

Belt latch
It should be secure when latched.

INSTALLATION

Install in reverse order of removal, noting the following.

Seat belt anchor bolts should have an unified fine thread
(7/16–20 UNF). Under no circumstances should any different
sized or metric screw threads be used.

Be sure to tighten seat belt anchor bolts to specified torque.

Tightening Torque
(a): 35 N·m (3.5 kg-m, 25.5 lb-ft)
(b): 5.5 N·m (0.55 kg-m, 4.0 lb-ft)

Be sure to tighten retractor assembly mounting bolt and screw
in the order (“A”, “B”) as shown in the figure.

Tightening Torque
(a): 35 N·m (3.5 kg-m, 25.5 lb-ft)

10-6

RESTRAINT SYSTEM

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

EAL Formula 523585 Assembly Instructions preview
Formula 523585
Бренд: EAL Страницы: 4
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Бренд: RAM Страницы: 76
Advantech TREK-550 Manual preview
TREK-550
Бренд: Advantech Страницы: 59
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Бренд: FALCON RIDGE Страницы: 8
Scosche 142HUD2 Manual preview
142HUD2
Бренд: Scosche Страницы: 8
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Skoda Fabia II 2007 Workshop Manual preview
Fabia II 2007
Бренд: Skoda Страницы: 165
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
Audi 2011 A3 Sportback Pricing And Specification Manual preview
2011 A3 Sportback
Бренд: Audi Страницы: 29
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Бренд: Safe Fleet Страницы: 12
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Бренд: r.LiNK Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды