manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

9

BODY SERVICE

9-1

SECTION 9

BODY SERVICE

WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an
authorized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” un-
der “General Description” in air bag system section in order to confirm whether you are perform-
ing service on or near the air bag system components or wiring. Please observe all WARNINGS
and “Service Precautions” under “On-Vehicle Service” in air bag system section before perform-
ing service on or around the air bag system components or wiring. Failure to follow WARNINGS
could result in unintentional activation of the system or could render the system inoperative. Ei-
ther of these two conditions may result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to
the “LOCK” position and the negative cable is disconnected from the battery. Otherwise, the sys-
tem may be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

When body servicing, if shock may be applied to air bag system component parts, remove those
parts beforehand. (Refer to Section 10B).

NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital compo-
nents and systems, and / or could result in major repair expense. They must be replaced with one of
the same part number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used
as specified during reassembly to assure proper retention of these parts.

CONTENTS

GLASS AND WINDOWS AND MIRRORS

9- 2

. . . . . 

Front Door Glass

9- 2

. . . . . . . . . . . . . . . . . . . . . . . . 

Front Door Window Regulator

9- 5

. . . . . . . . . . . . . 

Windshield

9- 6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Rear Door Glass

9-12

. . . . . . . . . . . . . . . . . . . . . . . . . 

Rear Door Window Regulator

9-14

. . . . . . . . . . . . . . 

Back Door Glass

9-15

. . . . . . . . . . . . . . . . . . . . . . . . . 

BODY STRUCTURE

9-16

. . . . . . . . . . . . . . . . . . . . . . . 

Front Door Assembly

9-16

. . . . . . . . . . . . . . . . . . . . . 

Rear Door Assembly

9-16

. . . . . . . . . . . . . . . . . . . . . 

Back Door Assembly

9-17

. . . . . . . . . . . . . . . . . . . . . 

Hood

9-19

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Front Fender

9-20

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Bumpers

9-21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Body Dimensions

9-22

. . . . . . . . . . . . . . . . . . . . . . . . 

Under Body Dimensions

9-25

. . . . . . . . . . . . . . . . . . 

INSTRUMENTATION AND DRIVER

INFORMATION

9-27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Instrument Panel

9-27

. . . . . . . . . . . . . . . . . . . . . . . . . 

SEAT

9-28

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Front Seat

9-28

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Rear Seat

9-29

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

PAINT AND COATINGS

9-30

. . . . . . . . . . . . . . . . . 

Anti-Corrosion Treatment

9-30

. . . . . . . . . . . . . . 

Metal Replacement Parts Finishing

9-31

. . . . . . 

Sealant application area

9-32

. . . . . . . . . . . . . . . 

Under coating/anti-corrosion 

compound application area

9-37

. . . . . . . . . . . . 

Plastic Parts Finishing

9-39

. . . . . . . . . . . . . . . . . 

SECURITY AND LOCKS

9-40

. . . . . . . . . . . . . . . . 

Front Door Lock Assembly

9-40

. . . . . . . . . . . . . 

Rear Door Lock Assembly

9-41

. . . . . . . . . . . . . 

Back Door Lock Assembly

9-41

. . . . . . . . . . . . . 

Key Coding

9-42

. . . . . . . . . . . . . . . . . . . . . . . . . . 

EXTERIOR AND INTERIOR TRIM

9-43

. . . . . . . . 

Floor Carpet

9-43

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Head lining

9-44

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Pacbrake 10475 Installation Manual preview
10475
Бренд: Pacbrake Страницы: 9
Vauxhall MOVANO Owner'S Manual preview
MOVANO
Бренд: Vauxhall Страницы: 177
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Бренд: SAN HIMA Страницы: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Бренд: Paccar Страницы: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Бренд: Mercedes-Benz Страницы: 153
Ranger design 1525-NS Installation Manual preview
1525-NS
Бренд: Ranger design Страницы: 22
National Cycle Quantum hardcoated N30216 Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30216
Бренд: National Cycle Страницы: 3
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
Rydeen BSS2 Owner'S Manual preview
BSS2
Бренд: Rydeen Страницы: 14
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Бренд: Dodge Страницы: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Бренд: Lexus Страницы: 108
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Бренд: Toyota Страницы: 204
INNO TR163 Installation Instructions preview
TR163
Бренд: INNO Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды