manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

RADIATOR FAN CONTROL SYSTEM

SYSTEM INSPECTION

WARNING:
Keep hands, tools, and clothing away from engine cool-
ing fan to help prevent personal injury. This fan is electric
type and can turn on whether or not the engine is run-
ning. The fan can start automatically in response to the
ECT sensor with the ignition switch at ON position.

Start engine and keep it running to warm it up.
Now check to ensure that radiator fan in turns on and off when indi-
cator of coolant temp. meter moves to the level as shown in the fig-
ure.
If check result is not satisfactory, check radiator fan control relay,
wire harness, ECT sensor, ECM/PCM and coolant temp. meter.
Refer to TABLE B-8 RADIATOR FAN CONTROL SYSTEM
CHECK, ENGINE COOLANT TEMPERATURE METER INSPEC-
TION AND ENGINE COOLANT TEMPERATURE SENSOR IN-
SPECTION in SECTION 8B.

RADIATOR FAN CONTROL RELAY

INSPECTION

1) Disconnect negative cable at battery.
2) Remove radiator fan control relay (1) from fuse/relay box.
3) Structure of radiator fan control relay is the same as that of main

relay. (Refer to MAIN RELAY of ECM/PCM POWER SUPPLY
SYSTEM in this section.)
Measure its resistance and operation using the same proce-
dure as that for main relay. (Refer to MAIN RELAY of ECM/PCM
POWER SUPPLY SYSTEM in this section.) 
If found defective, replace.

1

EGR SYSTEM

SYSTEM INSPECTION

NOTE:
Before inspection, check to make sure that gear shift lever is
in neutral position (with A/T model, selector lever in “P”
range) and that parking brake lever is pulled all the way up.

ENGINE AND EMISSION CONTROL SYSTEM

6E1-71

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
EAL Formula 523585 Assembly Instructions preview
Formula 523585
Бренд: EAL Страницы: 4
Metra Electronics 95-6556 Installation Instructions preview
95-6556
Бренд: Metra Electronics Страницы: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Бренд: Rostra Страницы: 2
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Бренд: Honda Страницы: 208
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Бренд: hc-cargo Страницы: 60
StowAway 2 025.41 Assembly Instructions preview
025.41
Бренд: StowAway 2 Страницы: 2
Kia Picanto Manual preview
Picanto
Бренд: Kia Страницы: 680
Lexus 2010 RX 350 Warranty And Services Manual preview
2010 RX 350
Бренд: Lexus Страницы: 82
OMNISTOR Omni-Bike Sport Ducato Installation preview
Omni-Bike Sport Ducato
Бренд: OMNISTOR Страницы: 5
HUSKY LINERS 47954 Installation Instructions preview
47954
Бренд: HUSKY LINERS Страницы: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Бренд: iOttie Страницы: 19
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Бренд: Federal Signal Corporation Страницы: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Бренд: Kia Страницы: 216
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Бренд: Mercedes-Benz Страницы: 66
GEMINI TECHNOLOGY 514F User Manual preview
514F
Бренд: GEMINI TECHNOLOGY Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды