manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

TIRE PLACARD

The tire placard is located on the left door (right door for righthand
side steering vehicle) lock pillar and should be referred to for tire
information.
The placard lists the maximum load, tire size and cold tire pressure
where applicable.

NOTE:
Whether rim size and/or maximum load are listed or not de-
pends on regulations of each country.

TIRE ROTATION

To equalize wear, rotate tires according to left figure. Radial tires
should be rotated periodically. Set tire pressure.

NOTE:
Due to their design, radial tires tend to wear faster in the
shoulder area, particularly in front positions. This makes reg-
ular rotation especially necessary.

[LH]

[RH]

3F-4

WHEEL AND TIRES

INFLATION OF TIRES

The pressure recommended for any model is carefully calculated to give a satisfactory ride, stability, steering, tread
wear, tire life and resistance to bruises.
Tire pressure, with tires cold, (after vehicle has set for three hours or more, or driven less than one mile) should
be checked monthly or before any extended trip. Set to the specifications on the tire placard located on the left door
(right door for right-hand side steering vehicle) lock pillar.
It is normal for tire pressure to increase when the tires become hot during driving.
Do not bleed or reduce tire pressure after driving. Bleeding reduces the “Cold Inflation Pressure”.

Higher than recommended pressure can cause:
1. Hard ride
2. Tire bruising or carcass damage
3. Rapid tread wear at center of tire

Unequal pressure on same axle can cause:
1. Uneven braking
2. Steering lead
3. Reduced handling
4. Swerve on acceleration

Lower than recommended pressure can cause:
1. Tire squeal on turns
2. Hard Steering
3. Rapid and uneven wear on the edges of the tread
4. Tire rim bruises and rupture
5. Tire cord breakage
6. High tire temperature
7. Reduced handling
8. High fuel consumption
Valve caps should be on the valves to keep dust and water out.

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Xblitz G250 User Manual preview
G250
Бренд: Xblitz Страницы: 16
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Бренд: Ford Страницы: 12
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Бренд: Renault Страницы: 238
Harbor Freight Tools 66242 User Manual preview
66242
Бренд: Harbor Freight Tools Страницы: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Бренд: Honda Страницы: 3
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Бренд: SAN HIMA Страницы: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Бренд: Paccar Страницы: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Бренд: Mercedes-Benz Страницы: 153
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Flash Cover MN002 Installation Manual preview
MN002
Бренд: Flash Cover Страницы: 2
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды