Suzuki RA410 Скачать руководство пользователя страница 197

Страница: 197 / 761

DISASSEMBLY
For Tripod joint type drive shaft (Righ side)

1) Remove differential side boot band, then take out tripod joint

housing (1).

2) Remove grease from shaft and take off snap ring (1) by using

special tool, then pull out spider (2) from shaft.

Special Tool
(A): 09900-06107

CAUTION:
To prevent needle bearing of joint from being de-
greased, do not wash it if it is to be reused.

3) Remove boot band, then pull out differential side boot from

shaft.

4) Undo band of dynamic damper, then pull out damper through

shaft.

5) Undo boot bands of wheel side joint boot, then pull out boot

through shaft.

CAUTION:

Disassembly of wheel side joint is not allowed. If
noise or damage exists in it, replace it as assembly.

Do not disassemble tripod joint spider. If any mal-
condition is found in it, replace it as differential side
joint assembly.

FRONT DRIVE SHAFT

4A-5

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RA410

Отзывы:

Похожие инструкции для RA410

Бренды по названию

Популярные бренды

Suzuki RA410, Руководство пользователя

Результаты поиска

Содержание RA410

Отзывы:

Похожие инструкции для RA410

Бренды по названию

Популярные бренды