manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

1) Install injector and fuel pressure regulator to special tool (injec-

tor checking tool).

NOTE:
Remove grommet from injector, then install injector to spe-
cial tool and tighten bolts by hand.

Special Tool
(A): 09912-58421

2) Connect special tools (hoses and attachment) to pipes of ve-

hicle.

Special Tool
(B): 09912-58431

3) Connect special tool (test lead) to injector.

Special Tool
(C): 09930-88521

1. Fuel feed pipe
2. Fuel injector
3. Fuel pressure regulator
4. Fuel return pipe

(C)

4) Install suitable vinyl tube (1) onto injector nozzle to prevent fuel

from splashing out when injecting.

5) Put graduated cylinder (2) under injector as shown in the figure.
6) Remove fuel pump relay.
7) To operate fuel pump and apply fuel pressure to injector, use

wire harness (3) as thick as the one used for fuel pump circuit
and connect terminals of fuel pump relay connector.

8) Apply battery voltage to injector for 15 seconds and measure in-

jected fuel volume with graduated cylinder.
Test each injector two or three times.
If not within specification, replace injector.

Injected fuel volume:
About 35.3 – 38.7 cc/15 sec. (0.075 – 0.081/0.062 – 0.068 US/
lmp. oz/15 sec.)

2

3

1

WARNING:
In order to reduce risk of fire and personal injury, keep
battery away from the cylinder as far as possible.

ENGINE AND EMISSION CONTROL SYSTEM

6E1-69

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

cam 2850 Mounting Instructions preview
2850
Бренд: cam Страницы: 2
Dapper Lighting 575 Install Manual preview
575
Бренд: Dapper Lighting Страницы: 2
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Бренд: hager Страницы: 9
RAM Ram 3500 2012 User Manual preview
Ram 3500 2012
Бренд: RAM Страницы: 116
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Бренд: Ford Страницы: 12
walser 30968 User Instructions preview
30968
Бренд: walser Страницы: 24
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Бренд: Firestone Страницы: 4
Great Wall WEY VV5 Service Manual preview
WEY VV5
Бренд: Great Wall Страницы: 18
WIX WP9378 Installation Instruction preview
WP9378
Бренд: WIX Страницы: 2
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
Fiat 500L 2020 Owner'S Manual preview
500L 2020
Бренд: Fiat Страницы: 284
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Summit Racing SUM-G1083 Assembly & Use Instructions preview
SUM-G1083
Бренд: Summit Racing Страницы: 11
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Бренд: Menabo Страницы: 8
Westin 32-2250 Instructions preview
32-2250
Бренд: Westin Страницы: 3
JBA 1528S Installation Instructions And Warranty Information preview
1528S
Бренд: JBA Страницы: 5
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77

Бренды по названию

Популярные бренды

Загрузить еще бренды