manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

INSTALLATION

1) When positioning thermostat (1) on thermostat case (2), be

sure to position it so that air bleed valve (3) comes at position
as shown in figure.

2

3

2) Install thermostat cap to thermostat case.
3) Connect cooling water hose.
4) Fill cooling system (refer to page 6B-6, 6B-7).
5) Install air cleaner case.
6) Connect negative cable at battery.
7) After installation, check each part for leakage.

WATER PUMP BELT

REMOVAL

1) Disconnect negative cable at battery.
2) Loosen drive belt adjusting bolt (2) and generator pivot bolts (3).

When servicing car equipped with A/C, remove compressor
drive belt before removing water pump belt (1).

4) Slacken belt by displacing generator and then remove it.

INSTALLATION

1) Install belt to water pump pulley, crankshaft pulley and genera-

tor pulley.
When servicing car equipped with A/C, install compressor drive
belt, too.

2) Adjust belt tension.

For Adjustment of compressor drive belt tension, refer to SEC-
TION 0B of this manual.

3) Tighten water pump belt adjusting bolt and pivot bolts.
4) Connect negative cable at battery.

WATER PUMP BELT TENSION INSPECTION AND AD-
JUSTMENT

For this inspection or adjustment, refer to WATER PUMP BELT
TENSION.

6B-10

ENGINE COOLING

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Бренд: Dometic GROUP Страницы: 20
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Бренд: Axxess Страницы: 4
Vintage Air 473275 Manual preview
473275
Бренд: Vintage Air Страницы: 14
Masterack RM470057 Assembly Instructions preview
RM470057
Бренд: Masterack Страницы: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Бренд: Over Armour Offroad Страницы: 5
Softride 26428 Instructions preview
26428
Бренд: Softride Страницы: 4
JBL smartbase Quick Start Manual preview
smartbase
Бренд: JBL Страницы: 12
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
Navman T1 F20 User Manual preview
T1 F20
Бренд: Navman Страницы: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Бренд: Macrom Страницы: 10
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Бренд: Ford Страницы: 2
Renault Laguna III Manual preview
Laguna III
Бренд: Renault Страницы: 3699
Toyota Tacoma 05 Brochure & Specs preview
Tacoma 05
Бренд: Toyota Страницы: 26
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Бренд: Quadratec Страницы: 20
TRAMEC CV 1 Series Manual preview
CV 1 Series
Бренд: TRAMEC Страницы: 116
Classic Accessories Quad Gear 18-029-010401-00-SC Instructions preview
Quad Gear 18-029-010401-00-SC
Бренд: Classic Accessories Страницы: 4
T-Rex TEX-51127 Installation Manual preview
TEX-51127
Бренд: T-Rex Страницы: 9
Chrysler 2005 300 Manual preview
2005 300
Бренд: Chrysler Страницы: 374

Бренды по названию

Популярные бренды

Загрузить еще бренды