manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

1) When engine is cool (coolant temperature is below 40

5

C

(104

5

F)), start engine and race it (higher than about 2000 rpm),

and check that EGR valve diaphragm (1) is not operating in this
state.

CAUTION:
If EGR valve is hot, it may be necessary to wear gloves
to avoid burning fingers.

1

2) Warm up engine to normal operating temperature and race it af-

ter warming up. Then check to be sure that diaphragm (1)
moves toward “A” in the figure during acceleration and toward
“B” during deceleration.
If EGR valve fails to operate properly, check vacuum hoses,
EGR valve, EGR back pressure transducer (2) and EGR sole-
noid vacuum valve.

“A”

“B”

2

1

3) Keep engine running at idle speed and open EGR valve by

hand, and engine should either stop or reduce its speed.
If neither occurs, EGR passage is clogged. Clean it.

EGR BACK PRESSURE TRANSDUCER

INSPECTION

1) Check filter (1) for contamination and damage.

Using compressed air, clean filter.

1

2) Remove EGR back pressure transducer (1) and plug nozzle

with finger. Blow air into another nozzle and check that air
passes through to air filter side (2) freely.

2

6E1-72

ENGINE AND EMISSION CONTROL SYSTEM

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

EAL Formula 523585 Assembly Instructions preview
Formula 523585
Бренд: EAL Страницы: 4
Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
BMW M5 2014 Service And Warranty Information preview
M5 2014
Бренд: BMW Страницы: 38
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Бренд: FALCON RIDGE Страницы: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Бренд: Volvo Страницы: 30
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Бренд: walser Страницы: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Бренд: Mercedes-Benz Страницы: 373
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Бренд: CITROËN Страницы: 164
Directed MIT4 Firmware Specific Manual preview
MIT4
Бренд: Directed Страницы: 30
Metra Electronics 99-9302 Installation Instructions Manual preview
99-9302
Бренд: Metra Electronics Страницы: 8
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Бренд: T.J.M. Страницы: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Бренд: Audi Страницы: 4
LaserLine 921K Operating Instructions preview
921K
Бренд: LaserLine Страницы: 4
Cadillac CTS 2011 Manual preview
CTS 2011
Бренд: Cadillac Страницы: 78
American muscle 71324 Manual preview
71324
Бренд: American muscle Страницы: 3
Car-Interface TV-Free CI-TF-C25 Manual preview
TV-Free CI-TF-C25
Бренд: Car-Interface Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды