manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

1

1

DRIVER AIR BAG (INFLATOR) MODULE
(FOR VEHICLE WITH AIR BAG SYSTEM)

WARNING:
When handling an air bag (inflator) module, be sure to
read SERVICE PRECAUTIONS in SECTION 10B and ob-
serve each instruction. Failure to follow them could
cause a damage to the air bag (inflator) module or result
in personal injury.

REMOVAL

1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYS-

TEM under SERVICE PRECAUTIONS in SECTION 10B.

3) Loosen 2 bolts (1) mounting driver air bag (inflator) module on

its both side.

4) Remove driver air bag (inflator) module (3) from steering wheel.
5) Disconnect yellow connector (1) of driver air bag (inflator) mod-

ule and horn connector (2) in order a)–d) shown in the figure.

1

d)

a)

d)

b)

c)

INSPECTION

WARNING:
Never disassemble driver air bag (inflator) module or
measure its resistance. Otherwise, personal injury may
result.

CAUTION:
If air bag (inflator) module was dropped from a height of
90 cm (3 ft) or more, it should be replaced.

2

1

Check air bag (inflator) module visually and if any of the following
is found, replace it with a new one.

Air bag being deployed

Trim cover (pad surface) (1) being cracked

Wire harness or connector (2) being damaged

Air bag (inflator) module being damaged or having been ex-
posed to strong impact (dropped)

3C-4

STEERING WHEEL AND COLUMN

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Jeep Renegade Owner'S Handbook Manual preview
Renegade
Бренд: Jeep Страницы: 212
Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Бренд: Yakima Страницы: 8
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 4
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Бренд: Carax Страницы: 2
3SIXT 3S-1186 Operating Instructions Manual preview
3S-1186
Бренд: 3SIXT Страницы: 12
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Бренд: Mazdaspeed Страницы: 8
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Бренд: John Gold Страницы: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Бренд: Whispbar Страницы: 14
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
SuperATV Roof Installation Instructions Manual preview
Roof
Бренд: SuperATV Страницы: 7
Thule 1430 Kit Instructions Manual preview
1430 Kit
Бренд: Thule Страницы: 8
Improved Racing E5G-601 Instructions Manual preview
E5G-601
Бренд: Improved Racing Страницы: 17
AL-KO AKS 1300 Operating Instructions Manual preview
AKS 1300
Бренд: AL-KO Страницы: 40
Green Valley 601951 Instructions Manual preview
601951
Бренд: Green Valley Страницы: 17
Yenkee YAC 450 User Manual preview
YAC 450
Бренд: Yenkee Страницы: 22
Flash Cover MN012 Installation Manual preview
MN012
Бренд: Flash Cover Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды