manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

Right Side

Using similar procedure to above-mentioned procedure, set 
dial gauge tip to gear (1) shoulder.
Move gear up and down by hand and read dial gauge.

Special Tool
(A): 09900-20606
(B): 09900-20701

Right side

2) If thrust play is out of specification, select suitable thrust washer

from among the following available size, install it and check
again that specified gear play is obtained.

3) Drive in differential pinion shaft (1).
4) Press-fit left bearing (2) using special tool and copper hammer. 

Special  Tools
(A): 09951-76010

2

1

5) Hold differential assembly with soft jawed vise (1), install final

gear (2) and then tighten it with 8 bolts (3) to specified torque.

CAUTION:
Use of any other bolts than specified ones is prohib-
ited.

Tightening Torque
(a): 90 N

•

m (9.0 kg-m, 65.0 lb-ft)

1

3

2

6) Install exciter ring (1), directing as shown.

7A-26

MANUAL TRANSMISSION

Available thrust
washer thickness

0.9, 1.0 and 1.1 mm
(0.035, 0.039 and 0.043 in.)

bearing (2) is floating, and then press-fit right bearing (3) using
special tool and copper hammer.

Special Tool
(A): 09951-76010
(B): 09951-16060

7) Support differential assembly as shown in left figure so as to left

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Бренд: Ultra-tow Страницы: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Бренд: Mercedes-Benz Страницы: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Бренд: Menabo Страницы: 8
Camtree G-51 Instruction Manual preview
G-51
Бренд: Camtree Страницы: 5
Rightline Gear Car Top Duffle Bag Setup Manual preview
Car Top Duffle Bag
Бренд: Rightline Gear Страницы: 2
BESAFE iZi Flex Manual preview
iZi Flex
Бренд: BESAFE Страницы: 4
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Бренд: CITROËN Страницы: 301
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Бренд: Toyota Страницы: 52
Pacbrake HP10098 Installation Manual preview
HP10098
Бренд: Pacbrake Страницы: 6
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Бренд: SilverLeaf Electronics Страницы: 16
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Бренд: Soundoff Signal Страницы: 3
Truma Mover H SE User Manual preview
Mover H SE
Бренд: Truma Страницы: 10
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Бренд: Car-Interface Страницы: 23
TOP VEHICLE TECH GR3FORD5 Installation Manual preview
GR3FORD5
Бренд: TOP VEHICLE TECH Страницы: 8
MiX Telematics FM 3617i Installation Manual preview
FM 3617i
Бренд: MiX Telematics Страницы: 39
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454

Бренды по названию

Популярные бренды

Загрузить еще бренды