manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

6) Stretch the deployment harness from the driver or passenger

air bag (inflator) module to its full length 10 m (33 ft) (1).

Special Tool 
(A): 09932-75030

7) Place a power source (3) near the shorted end of the deploy-

ment harness. Recommended application: 12 Volts minimum,
2 amps minimum. A vehicle battery is suggested.

8) Verify that the area around the air bag (inflator) module or seat

belt pretensioner is clear of all people and loose or flammable
objects.

9) [In case of Driver Air Bag (Inflater) Module]

Verify that the driver air bag (inflator) module is resting with its
vinyl trim cover facing up.

[In case of Passenger Air Bag (Inflator) Module]
Verify that the passenger air bag (inflator) module is firmly and
properly secured in passenger air bag (inflator) module de-
ployment fixture (special tool).
[In case of Seat Belt Pretensioner]
Verify that the seat belt pretensioner, is placed as shown in the
figure on the ground in the space just cleared.

10) Connect (2) the air bag (inflator) module or seat belt preten-

sioner  to the deployment harness connector and lock connec-
tor with lock lever.

11) Notify all people in the immediate area that you intend to

deploy/activate the air bag (inflator) module or seat belt pre-
tensioner.

NOTE:

When the air bag deploys and the pretensioner acti-
vates, the rapid gas expansion will create a substantial
report. Wear suitable ear protection. Notify all people in
the immediate area that you intend to deploy the air bag
(inflator) module or activate the seat belt pretensioner
and suitable ear protection should be worn.

When the driver air bag deploys and the pretensioner
activates, driver air bag (inflator) module and preten-
sioner (retractor assembly) may jump about 30 cm (1 ft)
vertically. This is a normal reaction of them to the force
of the rapid gas expansion inside the air bag and pre-
tensioner.

After the air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and byproducts
of the chemical reaction.

For Driver Air Bag (Inflator) Module

For Passenger Air Bag (Inflator) Module

3

3

For Seat Belt Pretensioner

3

1

2

(A)

10B-58

AIR BAG SYSTEM

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
A-Tach Mounts ST-1 Instructions preview
ST-1
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Бренд: A-Tach Mounts Страницы: 2
A-Tach Mounts 50206 Instructions preview
50206
Бренд: A-Tach Mounts Страницы: 2
Vaisala MD30 Setup Manual preview
MD30
Бренд: Vaisala Страницы: 24
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Бренд: Mitsubishi Страницы: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Бренд: Cadillac Страницы: 442
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
Volvo 2006 XC70 Owner'S Manual preview
2006 XC70
Бренд: Volvo Страницы: 211
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Бренд: v.LOGiC Страницы: 22
JSPORT JSRLP024 Installation Instructions preview
JSRLP024
Бренд: JSPORT Страницы: 2
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Бренд: Safe Fleet Страницы: 12
N.R. AUTOSEATS Top User Manual preview
Top
Бренд: N.R. AUTOSEATS Страницы: 8
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3
G-Tech Pro Competition User Manual preview
Pro Competition
Бренд: G-Tech Страницы: 180
LetsGoAero V2 Two-Bike Carrier User Manual preview
V2 Two-Bike Carrier
Бренд: LetsGoAero Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды