manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

REMOVAL

1) Remove console box.
2) Disconnect gear shift & select control cables from gear shift

lever assembly.

3) Remove 4 gear shift control cable guide nuts and gear shift

lever assembly from body.

4) Disconnect shift & select cables from transmission.
5) Remove E-rings, cable grommet and cable clamp, and then

remove shift & select cables from body.

INSTALLATION

1) Apply grease to turning or sliding portions.
2) If knob has been removed from lever, apply thread lock cement

and then install knob to control lever. Make sure that knob is
aligned with lever.

3) Install control lever assembly and related parts as they were.

For positioning control lever, loosely install 4 gear shift control
cable guide nuts, adjust position and then tighten nuts. (Refer
to page 7A-8.)

NOTE:

Make sure that boots are installed correctly.

Check control lever for smooth movement after assem-
bly.

VEHICLE SPEED SENSOR (VSS)

REMOVAL

1) Disconnect negative cable at battery.
2) Disconnect VSS coupler (1).
3) Remove VSS (2).

2

1

INSTALLATION

1) Check O-ring (1) and VSS (2) surface for their flawlessness, ap-

ply oil to O-ring and install VSS to transmission.

Tightening Torque
(a): 5 N·m (0.5 kg-m, 3.5 lb-ft)

2) Connect VSS coupler.
3) Connect negative cable at battery.

2

1

(a)

MANUAL TRANSMISSION

7A-9

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Daihatsu Mira Manual preview
Mira
Бренд: Daihatsu Страницы: 340
Warrior Products 3860 Quick Start Manual preview
3860
Бренд: Warrior Products Страницы: 2
RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Бренд: RACLET Страницы: 48
RACLET Allegra Manual preview
Allegra
Бренд: RACLET Страницы: 31
Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Бренд: Paccar Страницы: 20
GMC SIERRA 2002 Manual preview
SIERRA 2002
Бренд: GMC Страницы: 499
Kia Amanti Owner'S Manual preview
Amanti
Бренд: Kia Страницы: 290
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Бренд: NavLinkz Страницы: 21
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
travall TDG-1301 Fitting Instruction preview
TDG-1301
Бренд: travall Страницы: 2
Gacell 13553 User Manual preview
13553
Бренд: Gacell Страницы: 12
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Бренд: Mynew Страницы: 5
Renault KANGOO BE BOP Driver'S Handbook Manual preview
KANGOO BE BOP
Бренд: Renault Страницы: 198
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Бренд: FALCON RIDGE Страницы: 6
Ford C-Max Energi 2014 Quick Reference Manual preview
C-Max Energi 2014
Бренд: Ford Страницы: 10
Hama MagLock Vent Operating Instructions Manual preview
MagLock Vent
Бренд: Hama Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды