manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

OIL PRESSURE CHECK

NOTE:
Prior to checking oil pressure, check the following items.

Oil level in oil pan.
If oil level is low, add oil up to Full level mark (hole) on oil
level gauge.

Oil quality.
If oil is discolored, or deteriorated, change it.
For particular oil to be used, refer to the table in Section 0B.

Oil leaks.
If leak is found, repair it.

1. Full level mark (hole)
2. Low level mark (hole)

1

2

1) Remove front bumper (refer to Section 9) and oil pressure

switch (1) from cylinder block.

1

2) Install special tool (Oil pressure gauge) to vacated threaded

hole.

Special Tool
(A): 09915-77310
(B): 09915-78211

3) Start engine and warm it up to normal operating temperature.

NOTE:
Be sure to place transmission gear shift lever in “Neutral”
(shift select lever to “P” range for A / T model), and set park-
ing brake and block drive wheels.

4) After warming up, raise engine speed to 4,000 r / min and mea-

sure oil pressure.

Oil pressure specification:
330 – 430 kPa (3.3 – 4.3 kg / cm

2

, 46.9 – 61.1 psi) at 4,000

r / min (rpm)

5) Stop engine and remove oil pressure gauge.

ENGINE MECHANICAL

6A4-7

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Бренд: iDataLink Страницы: 99
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Бренд: Pyle Страницы: 4
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Бренд: Scosche Страницы: 16
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Бренд: Calitop Страницы: 5
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Бренд: v.link Страницы: 21
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Бренд: ZAPTEC Страницы: 20
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Бренд: Dodge Страницы: 444
V8 equipment E.BEX Manual preview
E.BEX
Бренд: V8 equipment Страницы: 34
Phonocar VM 320 Instruction Manual preview
VM 320
Бренд: Phonocar Страницы: 28
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Бренд: Edelbrock Страницы: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Бренд: GMC Страницы: 439
LaserLine 921K Operating Instructions preview
921K
Бренд: LaserLine Страницы: 4
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454

Бренды по названию

Популярные бренды

Загрузить еще бренды