Suzuki RA410 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 761

background image

RADIATOR (AND CONDENSER) COOLING
FAN RELAY

INSPECTION

1) Disconnect negative (–) cable at battery.
2) Remove radiator cooling fan relay (1) from vehicle.
3) Connect battery positive (+) terminal to terminal “b” of relay.

Connect battery negative (–) terminal “a” of relay.
Check continuity between terminal “c” and “d”.
If there is no continuity when relay is connected to the battery,
replace relay.

2. Radiator (and condenser) cooling fan fuse

2

1

a

c

d

b

a

c

d

b

1

COMPRESSOR

REMOVAL

1) RUN engine at idle speed with air conditioning ON for 10 min-

utes. After that stop the engine.

2) Disconnect negatige (–) cable at battery.
3) Recover refrigerant from refrigeration system by using recovery

and recycling equipment.

4) Remove front bumper.
5) Disconnect magnet clutch lead wire (1) and undo lead wire

clamp (2).

1

2

6) Disconnect suction and discharge hoses from compressor.

NOTE
Cap open fittings immediately to keep moisture out of sys-
tem.

7) Remove compressor drive belt by loosening compressor bolt.
8) Remove compressor with magnet clutch assembly (3) from its

mount as shown.

9) If compressor is replaced.

Drain oil from compressor, and measure its amount.

3

INSTALLATION

Reverse removal procedure noting the following point.

If compressor is replaced, pour new compressor oil with the
same amount as that drained from compressor in REMOVAL.
Refer to “REPLENISHING COMPRESSOR OIL” in this section.

Evacuate and charge system according to previously described
procedure.

1. New compressor
2. Removed

compressor

3. Excess oil (A–B)

AIR CONDITIONING (OPTIONAL)

1B-19

«
...
69
70
71
72
73
...
»

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Бренд: GMC Страницы: 499

Бренд: Kia Страницы: 290

Бренд: Toyota Страницы: 371

Бренд: Whispbar Страницы: 15

Green Motion DC 66

Бренд: Eaton Страницы: 18

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: E&G Classics Страницы: 4

Бренд: Jaeger Страницы: 16

Бренд: Axxess Страницы: 8

Бренд: Autoplugin Страницы: 8

Бренд: Metra Electronics Страницы: 12

Бренд: Edelbrock Страницы: 2

Бренд: Rosco Страницы: 12

Бренд: JBA Страницы: 5

Бренд: WABCO Страницы: 40

Бренд: Dacia Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды