manualshive.com logo in svg

Suzuki RA410, Руководство пользователя


Поделиться
Скачать
background image

10B-54

AIR BAG SYSTEM

AIR BAG (INFLATOR) MODULE AND SEAT BELT PRETENSIONER
DISPOSAL

WARNING:
Failure to follow proper air bag (inflator) module and seat belt pretensioner disposal procedures can
result in air bag deployment and pretensioner activation which may cause personal injury.
Undeployed air bag (inflator) module/inactivated seat belt pretensioner must not be disposed of
through normal refuse channels.
The undeployed air bag (inflator) module and inactivated seat belt pretensioner contain substances
that can cause severe illness or personal injury if the sealed container is damaged during disposal.

Do not dispose of the live (undeployed) air bag (inflator) modules and seat belt pretensioners.
The method employed depends upon the final disposition of the particular vehicle, as noted in DEPLOYMENT/AC-
TIVATION OUTSIDE VEHICLE and DEPLOYMENT/ACTIVATION INSIDE VEHICLE.

Deployment/Activation  Outside  Vehicle

Follow this procedure when disposing of the air bag (inflator) mod-

. . . . . . 

ule(s) and seat belt pretensioner(s) only (i.e., the vehicle itself will
be used again).

Deployment/Activation Inside Vehicle

Follow this procedure when scrapping the entire vehicle including

. . . . . . . 

the air bag (inflator) modules and seat belt pretensioners.

WARNING:
Following precautions must be observed for this work. Failure to observe any of them may result in
personal injury.

The procedure should be followed strictly as described here.

Be sure to read SERVICE PRECAUTIONS in this section beforehand.

To avoid an accidental deployment, this work should be performed by no more than one person.

Since the smoke is produced when air bag is deployed and pretensioner is activated, select a well-
ventilated area.

The air bag (inflator) module and seat belt pretensioner will immediately deploy/activate when a
power source is connected to it. Wear safety glasses throughout this entire deployment/activation
and disposal procedure.

Wear suitable ear protection when deploying air bag/activating pretensioner. Also, advise those
who are in the area close to deployment/activation site to wear suitable ear protection.

Do not deploy/activate two or more air bag system components (air bag (inflator) modules and
seat belt pretensioners) at the same time.

Never connect deployment harness to any power source before connecting deployment harness
to the air bag (inflator) module and seat belt pretensioner. Deployment harness shall remain
shorted and not be connected to a power source until the air bag is to be deployed and the preten-
sioner is to be activated.

DEPLOYMENT/ACTIVATION OUTSIDE VEHICLE

Use this procedure when the vehicle itself is used again (only the air bag (inflator) module(s) and seat belt preten-
sioner(s) are disposed of).

Содержание RA410


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RA410

Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Бренд: Metra Electronics Страницы: 14
Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
Raven CR7 Calibration Manual preview
CR7
Бренд: Raven Страницы: 24
Weather Guard 237 Assembly And Installation Instructions preview
237
Бренд: Weather Guard Страницы: 4
OEM Audio Reference Series Manual preview
Reference Series
Бренд: OEM Audio Страницы: 29
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Бренд: Subaru Страницы: 21
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Бренд: Ford Страницы: 368
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Бренд: Mercedes-Benz Страницы: 39
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Бренд: Subaru Страницы: 298
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Бренд: Skoda Страницы: 324
Jeep WRANGLER 2017 User Manual preview
WRANGLER 2017
Бренд: Jeep Страницы: 292
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Mercedes-Benz 2007 SLR Mclaren Operator'S Manual preview
2007 SLR Mclaren
Бренд: Mercedes-Benz Страницы: 425
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Бренд: Porsche Страницы: 127

Бренды по названию

Популярные бренды

Загрузить еще бренды