manualshive.com logo in svg

Renesas SH7780 Series, Руководство по оборудованию

Серия продуктов Renesas SH7780 предлагает мощные и надежные микроконтроллеры для широкого спектра приложений. Вы можете скачать бесплатно Руководство по аппаратному обеспечению для этой серии продуктов на manualshive.com. Получите доступ к подробной информации о функциях и возможностях устройства для оптимального использования.

Поделиться
Скачать
background image

Section 18   Timer Unit (TMU) 

 

 

Rev.1.00  Dec. 13, 2005  Page 675 of 1286 

 

 REJ09B0158-0100 

18.6 Usage 

Notes 

18.6.1 Register 

Writes 

When writing to a TMU register, timer count operation must be stopped by clearing the start bit 
(STR5 to STR0) for the relevant channel in TSTR. 

Note that TSTR can be written to, and the UNF and ICPF bits in TCR can be cleared while the 
count is in progress. When the flags (UNF and ICPF) are cleared while the count is in progress, 
make sure not to change the values of bits other than those being cleared. 

18.6.2 

Reading from TCNT 

Reading from TCNT is performed synchronously with the timer count operation. Note that when 
the timer count operation is performed simultaneously with reading from a register, the 
synchronous processing causes the TCNT value before the count-down operation to be read as the 
TCNT value. 

18.6.3 

Reset RTC Frequency Divider Circuit 

When selecting the output clock of the on-chip RTC for the count clock, reset the RTC frequency 
divider circuit. 

18.6.4 External 

Clock 

Frequency 

Ensure that the external clock (TCLK) input frequency for channels 0, 1 and 2 does not exceed 
Pck/4. 

Содержание SH7780 Series





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7780 Series

Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
Datasat AP25 Installation And Operating Manual preview
AP25
Бренд: Datasat Страницы: 170
Yamaha DX7mega128 Install Manual preview
DX7mega128
Бренд: Yamaha Страницы: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Бренд: Yamaha Страницы: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Бренд: Yamaha Страницы: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Бренд: Yamaha Страницы: 49
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Бренд: ebm-papst Страницы: 16
AXIOMTEK tBOX330-870-FL Series Quick Installation Manual preview
tBOX330-870-FL Series
Бренд: AXIOMTEK Страницы: 2
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Бренд: Funkwerk Страницы: 2
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Бренд: Riverbed Страницы: 38
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Бренд: Danville Signal Processing Страницы: 35
Cisco MERAKI MX450 Installation Manual preview
MX450
Бренд: Cisco MERAKI Страницы: 4
EMTRUST CP75X User Manual preview
CP75X
Бренд: EMTRUST Страницы: 103
Network Critical SmartNA-X User Manual preview
SmartNA-X
Бренд: Network Critical Страницы: 200
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Бренд: Taiwan Commate Computer Inc. Страницы: 25
Greenlee 910FS Instruction Manual preview
910FS
Бренд: Greenlee Страницы: 52
ST STA309A Operation Manual preview
STA309A
Бренд: ST Страницы: 67

Бренды по названию

Популярные бренды

Загрузить еще бренды