Particle Measuring Systems LASAIR II 310, Руководство оператора

Страница: 188 / 231

Command List Command List
LASAIR II Operator’s Manual LASAIR II Operator’s Manual
Page Page
G-7 G-7
control of the instrument. This can be used as a check if an error occurs while control of the instrument. This can be used as a check if an error occurs while
executing another command. Using the
executing another command. Using the
KB KB
or or
KG KG
commands ensures that the commands ensures that the
serial communications will have control of the instrument. serial communications will have control of the instrument.
ISDELAY secs ISDELAY secs
Set inter-sample delay. This is the delay between the end of Set inter-sample delay. This is the delay between the end of
one sample, and the start of the next. The maximum value is 86399 seconds one sample, and the start of the next. The maximum value is 86399 seconds
(23:59:59).
(23:59:59).
ISON ISON
Return the sampling state of the box Return the sampling state of the box (1/0). (1/0).
ITYPE ITYPE
Return the instrument model. Return the instrument model.
IVER IVER
Return the instrument firmware version. Return the instrument firmware version.
KB [1/0] KB [1/0]
Keypad lockout enable/disable. Lockout is retained through a Keypad lockout enable/disable. Lockout is retained through a
power cycle. If power cycle. If this lockout i this lockout is disabled wit s disabled with the “ h the “
KG KG 0 0
” command, it will be re- ” command, it will be re-
enabled when the power is cycled. enabled when the power is cycled.
KG [1/0] KG [1/0]
Keypad lockout enable/disable. Lockout lasts until “ Keypad lockout enable/disable. Lockout lasts until “
KG 0” KG 0”
, “ , “
KB KB
0”, 0”,
or a power cycle or a power cycle
NORMDATA [1/ NORMDATA [1/0] 0]
Set normalized/raw particle display. If particle display is Set normalized/raw particle display. If particle display is
set to 0, then data is shown set to 0, then data is shown in raw counts on the display. In addition, if particle in raw counts on the display. In addition, if particle
alarms are used, the alarms automatically change with sample alarms are used, the alarms automatically change with sample time changes. time changes.
PALARM PALARM chan,value,[ chan,value,[1/0] 1/0]
Set particle alarm for specified channel. Set particle alarm for specified channel.
Channel is 1–6. Alarm value is any Channel is 1–6. Alarm value is any number greater than or equal to number greater than or equal to 0. Note: if 0. Note: if
value is set to 0, channel value is set to 0, channel must be disabled. An error will be returned if setting must be disabled. An error will be returned if setting
is to enable a channel with 0 as the value. is to enable a channel with 0 as the value.
Particle alarms are internally modified depending on sampling parameters. If Particle alarms are internally modified depending on sampling parameters. If
the box displays data in a normalized output, then this is not an
the box displays data in a normalized output, then this is not an issue. Otherwise, issue. Otherwise,
changing the sample size (either by changing the sample size (either by time or volume) will ratio-metrically change time or volume) will ratio-metrically change
the alarm setting. the alarm setting.
PALARMTYPE [C/D] PALARMTYPE [C/D]
Select particle alarm type. This is either cumulative or Select particle alarm type. This is either cumulative or
differential. differential.
PDELAY secs PDELAY secs
Set the purge delay. This is the time to wait before the Set the purge delay. This is the time to wait before the
beginning beginning of of the the first first sample. sample. The maxi The maximum mum value is value is 86399 seconds 86399 seconds (23:59:59). (23:59:59).
(Even if this is set to 0, there will be some (Even if this is set to 0, there will be some delay before a sample for the delay before a sample for the pump pump
to spin up. to spin up.
POP POP
This command erases the This command erases the oldest sample in the data oldest sample in the data buffer buffer. The command . The command
may be used in conjunction with the TF command to send the complete data may be used in conjunction with the TF command to send the complete data
buffer buffer, sample by sample. , sample by sample.
PRALARM [1/0] PRALARM [1/0]
Enable or disable print on alarm feature. When enabled, the Enable or disable print on alarm feature. When enabled, the
following conditions will cause an immediate printout: analog alarm, particle following conditions will cause an immediate printout: analog alarm, particle
alarm, pump error, laser failure. The printout lists the alarm condition, the
alarm, pump error, laser failure. The printout lists the alarm condition, the
location, and date/time.
location, and date/time.
SS SS
Start sampling. Start sampling.