Moog MSD Servo Drive Скачать руководство пользователя страница 302

Страница: 302 / 472

Positioning

Limit value monitoring becomes active when the speed reference exceeds the

maximum speed or the torque reference exceeds the maximum torque (see Section

"Limitations / Thresholds" on page 310).

Infinite positioning/speed mode

Monitoring is activated in infinite positioning (speed mode) when the speed

reference has been reached. If an ongoing positioning operation is interrupted with

"HALT", the "Reference reached" message is not sent in this phase. The message

only appears after the actual target position has been reached.

9.3.7 Switching with motor contactor

Switching in the power cable should only be carried out in a de-energized state.

Failure to follow this requirement may result in problems and damage (e.g.

overvoltage or overcurrent shutdowns, pitted contacts). To ensure currentless

switching, the contacts of the motor contactor must be closed before enabling the

power stage. In the opposite case the contacts must remain closed until the power

stage has been switched off. Corresponding safety time periods for the motor

contactor switching must be implemented in the control sequence of the machine or

else the special "ENMO" software function of the servo drive must be employed.

A power contactor in the motor supply line can be directly controlled by the servo

drive via parameter P 125[0] - MPRO_OUTPUT_FS_MOTOR_BRAKE = ENMO(21).

The timer P 148[0] - MPRO_DRVCOM_ENMO_Time defines the on-and-off delay of

the power contactor. Based on the time delay, the reference value is applied after

the power contactor is active. If the power stage is switched off, the power contactor

isolates the motor from the controller.

MOOG

ID No.: CB40859-001 Date: 11/2020

MSD Servo Drive - Device Help

302

9 Inputs/Outputs settings

NOTE

Additional times for the typical contact chatter on a contactor must
be taken into account when specifying the time for timer

P 148[0] -

MPRO_DRVCOM_ENMO_Time

. They may be several hundred

ms, depending on contactor.

Содержание MSD Servo Drive

























































































































































































































































































































































































































































































Результаты поиска

Содержание MSD Servo Drive

Отзывы:

Похожие инструкции для MSD Servo Drive

Бренды по названию

Популярные бренды

Moog MSD Servo Drive, Помощь по устройству

Результаты поиска

Содержание MSD Servo Drive

Отзывы:

Похожие инструкции для MSD Servo Drive

Бренды по названию

Популярные бренды