KEPCO BOP-ME 1KW, Руководство оператора

Страница: 89 / 234

BOP HIPWR 091719
3-13
TABLE 3-3. DISPLAY SETTINGS (OPERATOR CONVENIENCE) MENU
SETTING
CHOICES
( BOLD = Factory
Default)
FUNCTION
NOTE: To save any of the functions listed below for power-up it is necessary to first change SAVE DISPLAY CHG at the password
setup (see PAR. 3.2.4.2and Figure 3-6) from DISABLE to ENABLE.
Graphic Display Meters
75s
30s
15s
7.5s
3.8s
1.5s
0.8s
0.5s
0.3s
0.15s
Meters - Output voltage and current are displayed on representations of analog
meters.
75s through 0.15s - Displays a graph showing a sample of the output for the
time indicated (see Figure 3-5). The complete time-line uses 240 points. E.g.,
selecting 2 Second Graph means that 2S/240 = 50ms sampling, i.e., every
50ms a snapshot of the output state is used to produce a single point.
Display Background BLACK
WHITE
MonoBlack
BLUE
GREEN
Lt.Green
Lt.Blue
BLACK - Sets the background to black and displays white characters plus color
for voltage and current and special messages and warnings.
WHITE - Sets the background to white and displays black characters plus color
for voltage, current, special messages and warnings.
MonoBlack - Sets background and characters to either white or black only.
BLUE - Sets the background to blue and displays black characters plus color
for voltage, current, special messages and warnings.
GREEN - Sets the background to green and displays red characters plus color
for voltage, current, special messages and warnings.
Lt.Green - Sets the background to light green and displays black characters
plus color for voltage, current, special messages and warnings.
Lt.Blue - Sets the background to light blue and displays black characters plus
color for voltage, current, special messages and warnings.
Protect Entry Independent
Bipolar
Independent - and – protection limits to be set independently. from
the front panel (see PAR. 3.3.3.1 for considerations when using remote mode).
Bipolar - Causes a single protection limit value (one for voltage, one for cur-
rent) to apply to both ± limits. Only one value is displayed and edited from the
front panel. (see PAR. 3.3.3.1.)
Waveform Stop Output OFF
User Option
#
Stop Immediate
$
Stop & End Cycle
%
Output OFF
Output OFF - When waveform is stopped (either count complete or
%
pressed), output freezes at whatever level the waveform was at when
%
was
pressed or count completed, then after a brief delay output is set to STANDBY
(disabled).
User Option - Allows three choices during waveform execution
1. Press
#
to select Stop Immediate - When waveform is stopped (
%
pressed), output freezes at whatever level the waveform was at when
%
was
pressed.
2. Press
$
to select Stop and End Cycle - When waveform is stopped
(either count complete or
%
pressed), waveform runs through full cycle. The
output stops at the last generated value of the waveform (e.g., for a sinewave
segment of 0° to 270°, 10V amplitude, 0V offset, when
%
is pressed the out-
put will end up at -10V).
3. Press
%
to select Output OFF . This is the same as Output OFF described
above,
Key Press Beep On
Error Only
Off
On - provides an audible beep for each key press and for each error received.
Error Only - silences the beeps for each key press; errors will still cause beep.
Off - silences all beeps including key presses and errors except for power-up
and unit faults.
CONTRAST --- Use number keys 0 through 9 for coarse adjust. Use
T
and
R
for fine
adjust. Then press (
%
to exit or
$
to save for power up (see PAR. 3.2.5.1).