manualshive.com logo in svg

KEPCO BOP-ME 1KW, Руководство оператора

Операторская инструкция KEPCO BOP-ME 1KW доступна для бесплатного скачивания с нашего сайта. Этот мануал содержит все необходимые указания для работы с продуктом. Загружайте его прямо сейчас с manualshive.com и наслаждайтесь эффективной работой с этим уникальным устройством.

Поделиться
Скачать
background image

B-12

BOP-1K 091719

B.31

[SOURce:]CURRent[:LEVel]:LIMit:NEG COMMAND 

CURR:LIM:NEG

Syntax:

Short Form: [SOUR:]CURR[:LEV]:LIM:NEG <value>
Long Form: [SOURce:]CURRent[:LEVel]:LIMit:NEGative <value>

Description: Establishes the negative software limit <value> for output current, i.e., sets the maximum value of out-

put current that the unit will be allowed to source (quadrant 3, Figure 1-3) or sink (quadrant 2) to the
value specified by the user. Requires MEM:UPD (PAR. B.20) to save for power up. See PAR. 3.5.2.2
and Figure 3-19 for special programming considerations.

B.32

[SOURce:]CURRent[:LEVel]:LIMit:NEG? QUERY 

CURR:LIM:NEG?

Syntax:

Short Form: [SOUR:]CURR[:LEV]:LIM:NEG?
Long Form: [SOURce:]CURRent[:LEVel]:LIMit:NEGative?
Returns <value>

Description: Identifies the negative software limit value of output current that the unit can source (quadrant 3, Fig-

ure 1-3) or sink (quadrant 2).

B.33

[SOURce:]CURRent[:LEVel]:LIMit:POS COMMAND 

CURR:LIM:POS

Syntax:

Short Form: [SOUR:]CURR[:LEV]:LIM:POS <value>
Long Form: [SOURce:]CURRent[:LEVel]:LIMit:POSitive <value>
where <value> is between zero and the rated (nominal) output voltage

Description: Establishes the positive software limit <value> for output current, i.e., sets the maximum value of out-

put current that the unit will be allowed to source (quadrant 1, Figure 1-3) or sink (quadrant 4) to the
value specified by the user. Requires MEM:UPD (PAR. B.20) to save for power up. See PAR. 3.5.2.2
and Figure 3-19 for special programming considerations.

B.34

[SOURce:]CURRent[:LEVel]:LIMit:POS? QUERY 

CURR:LIM:POS?

Syntax:

Short Form: [SOUR:]CURR[:LEV]:LIM:POS?
Long Form: [SOURce:]CURRent[:LEVel]:LIMit:Positive?
Returns <value>

Description: Identifies the positive software limit value of output current that the unit can source (quadrant 1, Figure

1-3) or sink (quadrant 4).

B.35

[SOURce:]CURRent:MODE COMMAND 

CURR:MODE

Syntax:

Short Form: [SOUR:]CURR:MODE (FIX | LIST | TRAN <nn> | EXT | GAIN | PROT) 
Long Form: [SOURce:]CURRent:MODE (FIXed | LIST | TRANsient <nn> | EXTernal | GAIN | PROTect) 
nn = <value> = time in Seconds for transient (from 0.0005 to 2.0)

Description:

Allows the user to execute or stop a list, to execute a transient or to use an external reference in
voltage or current mode of operation.

 The default mode is FIXed: the power supply executes com-

mands normally, and LIST commands can be issued to establish the parameters and sequence of a
list. This command affects the 

main channel

, whether voltage or current.

When CURR:MODE LIST is issued, a list is executed (See LIST commands and Figure B-6). While

the list is being executed, all output and list change commands except CURR:MODE FIXed and
VOLT:MODE:FIXed are not accepted and will produce a command or settings conflict error.. 

Issuing CURR:MODE FIX while the list is running will stop the execution of the list and return power

     supply to settings in effect prior to running the list. If the list runs to completion, the settings of the last
     step of the list will be in effect. 

Issuing CURR:MODE HALT while the list is running will stop the execution of the list at the end of the

current cycle.

CURR:MODE TRAN nn causes the next CURR: or VOLT: command to produce a transient pulse of

nn Seconds duration. (Similar to VOLT:MODE TRAN (see PAR. B.111 for examples). If the time nn
exceeds 2 Seconds, error message -222 “dwell or frequency out range” is posted to the error queue. 

CURR:MODE EXT Configures the unit to use an external reference to change the main channel,

whether voltage or current (see PAR. 3.4). Identical to VOLT:MODE EXT. 

CURR:MODE GAIN Configures the unit to use an external reference to provide a proportional out-

put current. 

CURR:MODE PROT - allows CURR command to accept values up to the protection limits of the

power supply without generating an error. For example for a BOP 36-28MG in current mode, after
sending CURR:MODE PROT, sending CURR 28.3 would set the protection levels to 28.3 and main
channel level to 28.

Related Commands:

 CURR, LIST commands. (See example, Figure B-6.)

Содержание BOP-ME 1KW











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP-ME 1KW

Yokota TKA60 Manual preview
TKA60
Бренд: Yokota Страницы: 8
Gage Bilt GB784 Installation Instruction preview
GB784
Бренд: Gage Bilt Страницы: 13
Ganz GH Series Instruction Manual preview
GH Series
Бренд: Ganz Страницы: 8
Parkside 352083 2007 Original Instructions Manual preview
352083 2007
Бренд: Parkside Страницы: 78
Ofs Mya Assembly Instructions preview
Mya
Бренд: Ofs Страницы: 3
Parkside RAPIDFIRE Translation Of The Original Instructions preview
RAPIDFIRE
Бренд: Parkside Страницы: 64
Pattfield Ergo Tools PE-AGS 3,6 Li Original Operating Instructions preview
PE-AGS 3,6 Li
Бренд: Pattfield Ergo Tools Страницы: 88
Mitox 271MT Operator'S Manual preview
271MT
Бренд: Mitox Страницы: 40
NKO MACHINES B16ZERO Instruction Manual preview
B16ZERO
Бренд: NKO MACHINES Страницы: 16
Franke ACEX9001 Installation And Operating Instructions Manual preview
ACEX9001
Бренд: Franke Страницы: 89
Veeco MPS-3000 CE Technical Manual preview
MPS-3000 CE
Бренд: Veeco Страницы: 96
Slime 42012 Manual preview
42012
Бренд: Slime Страницы: 12
Xinpu XP-G80BE Handling Instructions Manual preview
XP-G80BE
Бренд: Xinpu Страницы: 12
Central Pneumatic Central Pneumatic 1/4" Stubby Air Ratchet 91002 Operating Instructions Manual preview
Central Pneumatic 1/4" Stubby Air Ratchet 91002
Бренд: Central Pneumatic Страницы: 8
Elektro-Automatik PSI 9000 WR 3U SLAVE Operating Manual preview
PSI 9000 WR 3U SLAVE
Бренд: Elektro-Automatik Страницы: 44
VOLTCRAFT DSP-3005 Operating Instructions Manual preview
DSP-3005
Бренд: VOLTCRAFT Страницы: 8
Daintree GE current Tetra GEPS24-100U-GLX Installation Manual preview
GE current Tetra GEPS24-100U-GLX
Бренд: Daintree Страницы: 3
Yamato SM 234 Instruction Manual preview
SM 234
Бренд: Yamato Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды