manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 996 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 996

IP Configuration Command Set

Reviewing IP Traffic and Configuring Routes

12-36

Matrix DFE-Platinum and Diamond Series Configuration Guide

12.2.6.2

set router limits route-table

Use this command to set the chassis-based route table limits.

set router limits route-table

 

route-table

Syntax Description

Command Type

Switch command.

Command Mode

Read-Write.

Command Defaults

None.

Example 

This example shows how to set the route table limit to 17000:

NOTE:

This command must be executed from the switch CLI.

 route-table

Sets the route table limit. Valid values are 1 - 25000. 

This parameter will also set the maximum allowable OSPF 
LSA Type 3 route limit to 8000, and the Type 5 limit to 
10,000. For more information on configuring OSPF, refer to 

Section 13.2.3

.

NOTE:

Values above the default size of 12000 routes 

require 256 Mb of memory throughout the entire chassis, 
and such values will be rejected if this memory upgrade is 
not installed.

Matrix(rw)->

set router limits route-table 17000

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов