manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1203 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1203

Routing Protocol Configuration Command Set

Configuring VRRP

Matrix DFE-Platinum and Diamond Series Configuration Guide

13-101

13.2.6.8

preempt

Use this command to enable or disable preempt mode on a VRRP router. Preempt is enabled on 
VRRP routers by default, which allows a higher priority backup router to preempt a lower priority 
master.

preempt vlan-id vrid 

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command disables preempt mode: 

no preempt vlan-id vrid

Command Type

Router command.

Command Mode

Router configuration: 

Matrix>Router1(config-router)#

Command Defaults

None.

Example

This example shows how to disable preempt mode on VLAN 1, VRID 1:

NOTE:

The router that owns the virtual router IP address always preempts other 

routers, regardless of this setting.

vlan vlan-id

Specifies the number of the VLAN on which to set preempt 
mode. This VLAN must be configured for IP routing as 
described in 

Section 2.3.2

.

vrid

Specifies a unique Virtual Router ID (VRID) associated 
with the routing interface.

 

Valid values are from 

1

 to 

255

.

Matrix>Router1(config)#

router vrrp

Matrix>Router1(config-router)#

no preempt vlan 1 1 

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов