manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1173 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1173

Routing Protocol Configuration Command Set

Configuring OSPF

Matrix DFE-Platinum and Diamond Series Configuration Guide

13-71

13.2.3.28 show ip ospf virtual-links

Use this command to display information about the virtual links configured on a router. A virtual 
link represents a logical connection between the backbone and a non-backbone OSPF area.

show ip ospf virtual-links

Syntax Description

None.

Command Type

Router command.

Command Mode

Any router mode.

Command Defaults

None.

Example

This example shows how to display OSPF virtual links information:

Table 13-6

 provides an explanation of the command output.

Matrix>Router1#

show ip ospf virtual-links

Virtual Link to router 5.5.5.1, is UP

 Transit area 0.0.0.2,via interface Vlan 7, Cost of using 10

 Transmit Delay is 1 sec(s), State POINT-TO-POINT

 Timer intervals configured:

                Hello 10, Dead 40, Wait 40, Retransmit 5

 Adjacency State FULL

Table 13-6

show ip ospf virtual links Output Details

Output

What It Displays...

Virtual Link

ID of the virtual link neighbor, and the virtual link status, 
which is up or down.

Transit area

ID of the transit area through which the virtual link is 
configured.

via interface

Router’s interface into the transit area.

Cost of using

OSPF cost of routing through the virtual link.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов