Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1394

Страница: 1394 / 1422

Security Configuration Command Set

Configuring Denial of Service (DoS) Prevention

14-184

Matrix DFE-Platinum and Diamond Series Configuration Guide

14.3.14.1 show hostdos

Use this command to display Denial of Service security status and counters.

show hostdos

Syntax Description

None,

Command Type

Router command.

Command Mode

Global configuration:

Matrix>Router1(config)#

Command Defaults

None.

Example

This example shows how to display Denial of Service security status and counters. For details on
how to set these parameters, refer to

Section 14.3.14.2

NOTE:

When fragmented ICMP packets protection is enabled, the Ping of Death

counter will not be incremented. Ping of Death is a subset of the fragmented ICMP
function.

Matrix>Router1(config)#

show hostdos

LANDd Attack (Destination IP = Source IP)

Disabled

Spoofed Address Check

Disabled

IP packet with multicast/broadcast source address

Always enabled

0 attacks

Fragmented ICMP traffic

Disabled

Large ICMP packet

Disabled

Ping-of-Death attack

Always enabled

0 attacks

Port Scanning

Disabled

«
...
1392
1393
1394
1395
1396
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1394 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: