manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1074 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1074

IP Configuration Command Set

Configuring Dynamic Host Configuration Protocol (DHCP)

12-114

Matrix DFE-Platinum and Diamond Series Configuration Guide

Commands

The commands used to configure DHCP are listed below and described in the associated section as 
shown:

•

ip dhcp server (

Section 12.2.9.1

) 

•

ip local pool (

Section 12.2.9.2

)

•

exclude (

Section 12.2.9.3

)

•

ip dhcp ping packets (

Section 12.2.9.4

)

•

ip dhcp ping timeout (

Section 12.2.9.5

)

•

ip dhcp pool (

Section 12.2.9.6

)

•

domain-name (

Section 12.2.9.7

)

•

dns-server (

Section 12.2.9.8

)

•

netbios-name-server (

Section 12.2.9.9

)

•

netbios-node-type (

Section 12.2.9.10

)

•

default-router (

Section 12.2.9.11

)

•

bootfile (

Section 12.2.9.12

)

•

next-server (

Section 12.2.9.13

)

•

option (

Section 12.2.9.14

)

•

lease (

Section 12.2.9.15

)

•

host (

Section 12.2.9.16

)

DHCP Host 
Configuration 
Mode

Configure DHCP 
host parameters.

Type 

client-identifier 

and 

the 

identifier

, or 

hardware-address 

and an

 address 

from 

any DHCP 
configuration mode.

Matrix>Router1
(config-dhcp-host)#

Table 12-12

DHCP Command Modes  (Continued)

Mode 

Usage

Access Method

Resulting Prompt

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов