manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1143 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1143

Routing Protocol Configuration Command Set

Configuring OSPF

Matrix DFE-Platinum and Diamond Series Configuration Guide

13-41

13.2.3.8

ip ospf transmit-delay

Use this command to set the amount of time required to transmit a link state update packet on an 
interface.

ip ospf transmit-delay seconds

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command resets the retransmit interval value to the default, 
1 second:

no ip ospf transmit-delay

Command Type

Router command.

Command Mode

Interface configuration: 

Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set the time required to transmit a link state update packet on VLAN 1 
at 20 seconds:

seconds

Specifies the transmit delay in seconds. Valid values are 
from 

1

 to 

65535

.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip ospf transmit-delay 20

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов