manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 986 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 986

IP Configuration Command Set

Reviewing and Configuring the ARP Table

12-26

Matrix DFE-Platinum and Diamond Series Configuration Guide

12.2.4.6

ip mac-address 

Use this command to set a MAC address on an interface.

ip mac-address address

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command clears the MAC address:

no ip mac-address 

Command Type

Router command.

Command Mode

Interface configuration: 

Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set an IP MAC address of 000A.000A.000B. on VLAN 1:

NOTE:

By default, every routing interface uses the same MAC address. If the user 

needs interfaces to use different MAC addresses, this command will allow it. It is the 
user’s responsibility to select a MAC address that will not conflict with other devices on 
the VLAN since the Matrix Series device will not automatically detect this conflict.

address

Specifies a 48-bit MAC address in hexadecimal format.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip mac-address 000A.000A.000B

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов