Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 955

Страница: 955 / 1422

Logging And Network Management Command Set

Configuring NetFlow

Matrix DFE-Platinum and Diamond Series Configuration Guide

11-165

11.2.8.10 set netflow export-version

Use this command to set the NetFlow flow record format used to export data. Refer to

Version

Support

on page 153

for more information about NetFlow version support. Use the

show netflow

config

command (

Section 11.2.8.1

) to display the current NetFlow version.

set netflow export-version

{

}

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write

Example

This example shows how to set the flow record format to Version 9

Specify the NetFlow flow record format to use when
exporting NetFlow packets, either Version 5 or 9.

The default is Version 5.

Matrix(rw)->

set netflow export-version 9

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 955 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: