manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 438 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 438

SNMP Configuration Command Set

Configuring SNMP Notification Parameters

5-52

Matrix DFE-Platinum and Diamond Series Configuration Guide

5.3.7

Configuring SNMP Notification Parameters

Purpose

To configure SNMP notification parameters and optional filters. Notifications are entities which 
handle the generation of SNMP v1 and v2 “traps” or SNMP v3 “informs” messages to select 
management targets. Optional notification filters identify which targets should not receive 
notifications. For a sample SNMP trap configuration showing how SNMP notification parameters 
are associated with security and authorization criteria (target parameters) and mapped to a 
management target address, refer to 

Section 5.3.8

.

Commands 

The commands used to configure SNMP notification parameters and filters are listed below and 
described in the associated section as shown.

•

show snmp notify (

Section 5.3.7.1

)

•

set snmp notify (

Section 5.3.7.2

)

•

clear snmp notify (

Section 5.3.7.3

)

•

show snmp notifyfilter (

Section 5.3.7.4

)

•

set snmp notifyfilter (

Section 5.3.7.5

)

•

clear snmp notifyfilter (

Section 5.3.7.6

)

•

show snmp notifyprofile (

Section 5.3.7.7

)

•

set snmp notifyprofile (

Section 5.3.7.8

)

•

clear snmp notifyprofile (

Section 5.3.7.9

)

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов