manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 302 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 302

Port Configuration Command Set

Setting Speed and Duplex Mode

4-42

Matrix DFE-Platinum and Diamond Series Configuration Guide

4.3.4

Setting Speed and Duplex Mode

Purpose

To review and set the operational speed in Mbps and the default duplex mode: 

Half

, for half duplex, 

or 

Full

, for full duplex for one or more ports.

Commands 

The commands used to review and set port speed and duplex mode are listed below and described 
in the associated section as shown.

•

show port speed (

Section 4.3.4.1

)

•

set port speed (

Section 4.3.4.2

)

•

show port duplex (

Section 4.3.4.3

)

•

set port duplex (

Section 4.3.6

)

NOTE:

These settings only take effect on ports that have auto-negotiation disabled.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов