Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1180

Страница: 1180 / 1422

Routing Protocol Configuration Command Set

Configuring DVMRP

13-78

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.4.2

ip dvmrp metric

Use this command to configure the metric associated with a set of destinations for DVMRP reports.

ip dvmrp metric metric

Syntax Description

Command Type

Router command.

Command Mode

Interface configuration:

Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set a DVMRP of 16 on VLAN 1:

metric

Specifies a metric associated with a set of destinations for
DVMRP reports. Valid values are from

. Entering

value will reset the metric back to the default value of

NOTE:

To reset the DVMRP metric back to the default value of 1, enter

ip dvmrp

metric 0

Matrix>Router1(config-if(Vlan 1))#

ip dvmrp metric 16

«
...
1178
1179
1180
1181
1182
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1180 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: