manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1029 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1029

IP Configuration Command Set

Configuring Load Sharing Network Address Translation (LSNAT)

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-69

12.2.8 Configuring Load Sharing Network Address Translation

(LSNAT)

About LSNAT

As defined in RFC 2391, LSNAT supports network reliability and availability by enabling high 
traffic servers to load balance. It allows an IP address and port number to become a Virtual IP 
address and port number (VIP), mapped to many devices. When the VIP is seen as a destination 
address and destination port number by the LSNAT device, the device traps the packet and then 
translates the VIP to a real IP address and port combination. It does this by using a selected 
algorithm for choosing from the group of servers addresses, and replaces the VIP with the selected 
IP address and port number. For outgoing transmissions, the translation is made from real IP address 
and port combination to VIP.

LSNAT Configuration Considerations

The following considerations must be taken into account when configuring LSNAT on Matrix 
Series devices:

•

On chassis-based systems, only one router per chassis will be allowed to run LSNAT at a given 
time.

•

ALL modules in the chassis must have upgraded memory to 256 MB, and must have an 
advanced license activated.

•

A server farm cannot be shared by different virtual servers.

•

When different virtual server IPs (VIPs) share the same real server in different server farms, the 
persistence level must be set the same.

•

All real servers in the same server farm should be configured to use the same port.

•

In general, in order to edit or delete a virtual server or real server (serverfarm) configuration, the 
devices must be first configured “out of service” (

no inservice

) before the changes will be 

allowed.

* Advanced License Required *

LSNAT is an advanced routing feature that must be enabled with a license key. If you have 
purchased an advanced license key, and have enabled routing on the device, you must activate 
your license as described in 

Section 2.2.4 

in order

 

to enable the LSNAT command set. If you wish 

to purchase an advanced routing license, contact Enterasys Networks Sales.

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов