Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 336

Страница: 336 / 1422

Port Configuration Command Set

Configuring Link Traps and Link Flap Detection

4-76

Matrix DFE-Platinum and Diamond Series Configuration Guide

4.3.8.6

set linkflap interval

Use this command to set the time interval (in seconds) for accumulating link down transitions.

set linkflap interval port-string

interval_value

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Examples

This example shows how to set the link flap interval on port fe.1.4 to 1000 seconds:

port-string

Specifies the port(s) on which to set the link flap interval.
For a detailed description of possible

port-string

values,

refer to

Section 4.1.1

interval_value

Specifies an interval in seconds. A value of 0 will set the
interval to forever.

Matrix(rw)->

set linkflap interval fe.1.4 1000

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 336 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: