Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 914

Страница: 914 / 1422

Logging And Network Management Command Set

Configuring Simple Network Time Protocol (SNTP)

11-124

Matrix DFE-Platinum and Diamond Series Configuration Guide

11.2.6.2

set sntp client

Use this command to set the SNTP operation mode.

set sntp client

{

broadcast

unicast

disable

}

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example shows how to enable SNTP in broadcast mode:

broadcast

Enables SNTP in broadcast client mode.

unicast

Enables SNTP in unicast (point-to-point) client mode. In
this mode, the client must supply the IP address from which
to retrieve the current time.

disable

Disables SNTP.

Matrix(rw)->

set sntp client broadcast

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 914 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: