manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 598 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 598

Process Overview: 802.1Q VLAN Configuration

Port Assignment Scheme

7-2

Matrix DFE-Platinum and Diamond Series Configuration Guide

7.1.1

Port Assignment Scheme

For information on this device’s port assignment scheme, refer to 

Section 4.1.1

.

7.1.2

Port String Syntax Used in the CLI

For information on how to designate port numbers in the CLI syntax, refer to 

Section 4.1.1

.

7.2

PROCESS OVERVIEW: 802.1Q VLAN CONFIGURATION 

Use the following steps as a guide to configure VLANs on the device (refer to the associated section 
in parentheses):

1.

Review existing VLANs (

Section 7.3.1

)

2.

Create and name VLANs (

Section 7.3.2

)

3.

Assign port VLAN IDs and ingress filtering (

Section 7.3.3

)

4.

Configure VLAN Egress (

Section 7.3.4

)

5.

Create a secure management VLAN (

Section 7.3.5

)

6.

Enable / Disable GVRP (GARP VLAN Registration Protocol) (

Section 7.3.6

)

Preparing for VLAN Configuration

A little forethought and planning is essential to a good VLAN implementation. Before attempting 
to configure a single device for VLAN operation, consider the following:

•

How many VLANs will be required?

•

What stations will belong to them?

•

What ports are connected to those stations?

•

What ports will be configured as GVRP-aware ports?

It is also helpful to sketch out a diagram of your VLAN strategy. 

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов