Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1004

Страница: 1004 / 1422

IP Configuration Command Set

Reviewing IP Traffic and Configuring Routes

12-44

Matrix DFE-Platinum and Diamond Series Configuration Guide

12.2.6.8

ip route

Use this command to add or remove a static IP route.

ip route prefix mask

{

forward-addr

vlan vlan-id

}

[

distance

] [

permanent

] [

tag

value

]

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command removes the static IP route:

no ip route prefix mask

{

forward-addr

vlan vlan-id

}

Command Type

Router command.

Command Mode

Global configuration:

Matrix>Router1(config)#

Command Defaults

•

distance

is not specified, the default value of 1 will be applied.

•

permanent

and

tag

are not specified, the route will be set as non-permanent

with no tag assigned.

prefix

Specifies a destination IP address prefix.

mask

Specifies a destination prefix mask.

forward-addr

vlan vlan-id

Specifies a forwarding (gateway) IP address or routing
(VLAN) interface ID.

distance

(Optional) Specifies an administrative distance metric for
this route. Valid values are

(default)

255

. Routes with

lower values receive higher preference in route selection.

permanent

(Optional) Specifies a permanent route.

tag value

(Optional) Specifies a tag for this route. Valid values are

4294967295

«
...
1002
1003
1004
1005
1006
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1004 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: