manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1144 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1144

Routing Protocol Configuration Command Set

Configuring OSPF

13-42

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.3.9

ip ospf hello-interval

Use this command to set the number of seconds a router must wait before sending a hello packet to 
neighbor routers on an interface. Each Matrix Series routing module or standalone device can 
support communications between up to 60 neighboring routers.

ip ospf hello-interval

 

seconds

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command sets the hello interval value to the default (10 
seconds for broadcast and point-to-point networks, 30 seconds for non-broadcast 
and point-to-multipoint networks):

no ip ospf hello-interval

Command Type

Router command.

Command Mode

Interface configuration:

 Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set the hello interval to 5 for VLAN 1:

seconds

Specifies the hello interval in seconds. Hello interval must 
be the same on neighboring routers (on a specific subnet), 
but can vary between subnets. This parameter is an unsigned 
integer with valid values between 

1

 and 

65535

.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip ospf hello-interval 5

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов