Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1114

Страница: 1114 / 1422

Routing Protocol Configuration Command Set

Configuring RIP

13-12

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.2.8

ip rip receive version

Use this command to set the RIP version(s) for update packets accepted on the interface.

ip rip receive version

{

2 | 1 2 | none

}

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command restores the default version of the RIP module
update packets that are accepted on the interface:

no ip rip receive

version

Command Type

Router command.

Command Mode

Interface configuration:

Matrix>Router1(config-if(Vlan 1))#

Command Defaults

None.

Example

This example shows how to set the RIP receive version to 2 for update packets received on VLAN 1:

Specifies RIP version 1.

Specifies RIP version 2.

1 2

Specifies RIP versions 1 and 2.

none

Specifies that no RIP routes will be processed on this
interface.

Matrix>Router1(config)#

interface vlan 1

Matrix>Router1(config-if(Vlan 1))#

ip rip receive version 2

«
...
1112
1113
1114
1115
1116
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1114 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: