Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 448

Страница: 448 / 1422

SNMP Configuration Command Set

Configuring SNMP Notification Parameters

5-62

Matrix DFE-Platinum and Diamond Series Configuration Guide

5.3.7.8

set snmp notifyprofile

Use this command to create an SNMP notify filter profile configuration. This associates a
notification filter, created with the

set snmp notifyfilter

command (

Section 5.3.7.5

), to a set of

SNMP target parameters to determine which management targets should not receive SNMP
notifications.

set snmp notifyprofile

profile targetparam targetparam

[

volatile

nonvolatile

]

Syntax Description

Command Defaults

If storage type is not

specified,

nonvolatile

(permanent) will be applied.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example shows how to create an SNMP notify profile named area51

and associate a target

parameters entry.

profile

Specifies an SNMP filter notify name.

targetparam
targetparam

Specifies an associated entry in the SNMP Target Params
Table.

volatile

nonvolatile

(Optional) Specifies a storage type.

Matrix(rw)->

set snmp notifyprofile

area51 targetparam v3ExampleParams

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 448 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: