manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1093 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1093

IP Configuration Command Set

Configuring Dynamic Host Configuration Protocol (DHCP)

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-133

12.2.9.17 client-class

Use this command to identify an DHCP client class. Using this command to give a set of client class 
properties a name, allows you to assign properties to all DHCP clients within the class rather than 
configuring each client separately. This command also enables DHCP class configuration mode.

client-class

 

name

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command deletes a client class name:

no client-class name

 

Command Type

Router command.

Command Mode

Any DHCP configuration mode.

Command Defaults

None.

Example

This example shows how to assign “clientclass1” as a client class name in the “localpool” address 
pool:

name

Specifies a name for a DHCP client class.

Matrix>Router1(config)#

ip dhcp pool localpool

Matrix>Router1(config-dhcp-pool)#

client-class clientclass1

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов