Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 1422

Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 27

Matrix DFE-Platinum and Diamond Series Configuration Guide

2-1

2

Startup and General Configuration

This chapter describes factory default settings and the Startup and General Configuration set of
commands.

2.1

STARTUP AND GENERAL CONFIGURATION SUMMARY

At startup, the Matrix Series device is configured with many defaults and standard features. The
following sections provide information on how to review and change factory defaults, how to
customize basic system settings to adapt to your work environment, and how to prepare to run the
device in router mode.

2.1.1

Factory Default Settings

The following tables list factory default device settings available on the Matrix Series device.

Table 2-1

lists default settings for Matrix Series switch operation.

Table 2-2

lists default settings for

router mode operation.

Table 2-1

Default Device Settings for Basic Switch Operation

Device Feature

Default Setting

CDP discovery
protocol

Auto enabled on all ports.

CDP authentication
code

Set to

00-00-00-00-00-00-00-00

CDP hold time

Set to

180

seconds.

CDP interval

Transmit frequency of CDP messages set to

60

seconds.

Cisco Discovery
Protocol

Globally auto-enabled, enabled on ports.

«
...
25
26
27
28
29
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов