Главная
/
Enterasys
/
Matrix 2G4072-52
/
Руководство по настройке

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1201 / 1422

Поделиться

Страница: 1201 / 1422

Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1201

Routing Protocol Configuration Command Set

Configuring VRRP

Matrix DFE-Platinum and Diamond Series Configuration Guide

13-99

13.2.6.7

critical-ip

Use this command to set a critical IP address for VRRP routing. A critical IP address defines an
interface — in addition to the interface between hosts and a first-hop router — that will prevent the
master router from functioning properly if the interface were to fail. For example, an IP address of
an interface connecting a master router to a router configured for internet access would be
considered a critical IP address for VRRP routing. Up to four critical IP addresses can be configured
on the device.

critical-ip vlan vlan-id vrid ip-address

[

critical-priority

]

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command clears the critical IP address:

no critical-ip vlan vlan-id vrid ip-address

Command Type

Router command.

Command Mode

Router configuration:

Matrix>Router1(config-router)#

Command Defaults

If not specified,

critical-priority

will be set to 10.

vlan vlan-id

Specifies the number of the VLAN on which to set the
critical IP address. This VLAN must be configured for IP
routing as described in

Section 2.3.2

.

vrid

Specifies a unique Virtual Router ID (VRID) associated
with the routing interface.

Valid values are from

1

to

255

.

ip-address

Specifies the IP address to set as the critical IP address.

critical-priority

(Optional) Specifies the value by which the VRID’s
priority will decrease as a critical IP becomes unavailable.

«
...
1199
1200
1201
1202
1203
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов