manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 993 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 993

IP Configuration Command Set

Configuring Broadcast Settings

Matrix DFE-Platinum and Diamond Series Configuration Guide

12-33

12.2.5.3

ip helper-address

Use this command to enable DHCP/BOOTP relay and the forwarding of local UDP broadcasts 
specifying a new destination address. This command works in conjunction with the 

ip 

forward-protocol 

command (

Section 12.2.5.2

), which defines the forward protocol and port 

number. You can use this command to add more than one helper address per interface. 

ip helper-address address

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command disables the forwarding of UDP datagrams to the 
specified address:

no ip helper-address address

Command Type

Router command.

Command Mode

Interface configuration:

 Matrix>Router(config-if(Vlan <vlan_id>))#

Command Defaults

None.

Example

This example shows how to permit UDP broadcasts from hosts on networks 191.168.1.255 and 
192.24.1.255 to reach servers on those networks:

address

Specifies a destination broadcast of host address used when 
forwarding.

Matrix>Router(config)#

ip forward-protocol udp

Matrix>Router(config)#

interface vlan 1

Matrix>Router(config-if(Vlan 1))#

ip helper-address 192.168.1.255

Matrix>Router(config)#

interface vlan 2

Matrix>Router(config-if(Vlan 2))#

ip helper-address 192.24.1.255

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов