Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1344

Страница: 1344 / 1422

Security Configuration Command Set

Configuring Multiple Authentication

14-134

Matrix DFE-Platinum and Diamond Series Configuration Guide

Commands

The commands used to configure multiple authentication are listed below and described in the
associated section as shown:

•

set multiauth mode (

Section 14.3.10.1

)

•

clear multiauth mode (

Section 14.3.10.2

)

•

set multiauth precedence (

Section 14.3.10.3

)

•

clear multiauth precedence (

Section 14.3.10.4

)

•

show multiauth port (

Section 14.3.10.5

)

•

set multiauth port (

Section 14.3.10.6

)

•

clear multiauth port (

Section 14.3.10.7

)

•

show multiauth station (

Section 14.3.10.8

)

•

clear multiauth station (

Section 14.3.10.9

)

•

show multiauth session (

Section 14.3.10.10

)

•

show multiauth idle-timeout (

Section 14.3.10.11

)

•

set multiauth idle-timeout (

Section 14.3.10.12

)

•

clear multiauth idle-timeout (

Section 14.3.10.13

)

•

show multiauth session-timeout (

Section 14.3.10.14

)

•

set multiauth session-timeout (

Section 14.3.10.15

)

•

clear multiauth session-timeout (

Section 14.3.10.16

)

NOTE:

In order for multiple authentication to function on the device, each possible

method of authentication (MAC authentication, PWA, 802.1X)

must be enabled globally

and configured appropriately on the desired ports per its corresponding command set
as described in this chapter.

Multiple authentication mode must be globally enabled on the device using the

set

multiauth mode

command as described in

Section 14.3.10.1

«
...
1342
1343
1344
1345
1346
...
»

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Matrix 2G4072-52

Отзывы:

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1344 / 1422

Результаты поиска

Содержание Matrix 2G4072-52

Отзывы: