manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 1138 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 1138

Routing Protocol Configuration Command Set

Configuring OSPF

13-36

Matrix DFE-Platinum and Diamond Series Configuration Guide

13.2.3.3

router id

Use this command to set the OSPF router ID for the device. The OSPF protocol uses the router ID 
as a tie-breaker for path selection. If not specified, this will be set to the lowest IP address of the 
interfaces configured for IP routing.

router id

 

ip-address

Syntax Description

Command Syntax of the “no” Form

The “no” form of this command resets the router ID to the first interface configured 
for IP routing:

no router id 

Command Type

Router command.

Command Mode

Router configuration: 

Matrix>Router1(config-router)#

Command Defaults

None.

Example

This example shows how to set the OSPF router ID to IP address 182.127.62.1:

ip-address

Specifies the IP address that OSPF will use as the router ID.

Matrix>Router1(config-router)#

router id 182.127.62.1

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов