manualshive.com logo in svg

Enterasys Matrix 2G4072-52, Руководство по настройке, Страница: 241 / 1422

Поделиться
Скачать
Enterasys Matrix 2G4072-52 Скачать руководство пользователя страница 241

Discovery Protocols Command Set

Link Layer Discovery Protocol and LLDP-MED

Matrix DFE-Platinum and Diamond Series Configuration Guide

3-45

3.2.4.12

set lldp med-fast-repeat

Network connectivity devices transmit only LLDP TLVs in LLDPDUs until they detect that an 
LLDP-MED endpoint device has connected to a port. At that point, the network connectivity device 
starts sending LLDP-MED TLVs at a fast start rate on that port. Use this command to set the number 
of successive LLDPDUs (with LLDP-MED TLVs) to be sent for one complete fast start interval.

set lldp med-fast-repeat

 

count

Syntax Description

Command Defaults

None.

Command Type

Switch command.

Command Mode

Read-Write.

Example

This example sets the number of fast start LLDPDUs to be sent to 4.

count

Specifies the number of fast start LLDPDUs to be sent 
when an LLDP-MED endpoint device is detected. Value 
can range from 2 to 10. Default is 3.

Matrix(rw)->set lldp med-fast-repeat 4

Содержание Matrix 2G4072-52















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов